This directive asks the sectioning commands \at-unit to place their units in separate hypertext pages. The pages are to terminate upon encountering any of the commands in the list \at-unit, \until-unit-1, \until-unit-2,...

       \CutAt{section,chapter}
       \tableofcontents
       \chapter{...}  ......  \section{...}  ......  \section{...}  ......
       \chapter{...}  ......  \section{...}  ......

A plus character `+', before the leading parameter, requests buttons that link to the hypertext pages; e.g., `\CutAt{+likesection}'.

The end points of sections not specified within the \CutAt commands can be made known with instructions of the form `\Configure{endunit}{unit,unit,...}'.

This variant of the \tableofcontents command specifies the kinds of entries that should be included in the tables.

This directive asks for a local table of contents, at each division created by the \at-unit command. The tables should include entries of types \unit-1, \unit-2,..., and terminate upon reaching any of the \at-unit, \until-unit-1, \until-unit-2,... commands.

Within the \TocAt instruction, the starred commands of LaTeX should be referenced with the prefix `like' instead of the postfix of `*', and appendices through the entry `appendix'.

       \TocAt{section,subsection,/likechapter}
       \CutAt{subsection,section,likechapter}
       
       \section{...} ... \subsection{...} ...
       \section{...} ... \subsection{...} ... \subsection{...} ...
       \chapter*{...}
       \section*{...} ...

       \TocAt*{section,subsection,/likechapter}

       \CutAt{subsection,section,likechapter}
       
       \section{...} ... \subsection{...} ...
       \section{...} ... \subsection{...} ... \subsection{...} ...
       \chapter*{...}
       \section*{...} ...

4. \ConfigureToc{unit} {before-mark} {before-title} {before-page-number} {at-end}

This command determines how entries of the specified unit will appear in the tables of contents. The entries include only fields corresponding to nonempty fields in the \ConfigureToc commands.

       \ConfigureToc{section} {} {$\bullet$~}  {}  {~~ }
       \tableofcontents[section]

5. \Configure{tableofcontents} {before-toc} {end-of-toc} {after-toc} {before-nonindented-par} {before-indented-par}

The end-of-toc is inserted at the end of the internal environment of the tables. The after-toc is included after leaving the internal environment.

This command determines the content to be inserted at the mentioned locations of the specified units.

       \Configure{chapter}
          {\HCode{<div class="chapter">}}  {\HCode{</div>}}
          {\HCode{<h2 class="chapterHead">}\chaptername
              ~\thechapter\HCode{<br />}}
          {\HCode{</h2>}}
       \chapter{...} ....
       \chapter{...} ....

This directive introduces a sectioning command \unit, which submits mark-for-toc to the tables of contents.

       \newcounter{c}
       \NewSection\X {\thec}
       \Configure{X}
          {\addtocounter{c}{1}\HCode{<h2>}[\thec] }
          {\HCode{</h2>}}
          {}{}

12. \Configure{crosslinks} {left-delimiter} {right-delimiter} {next} {prev} {prev-tail} {front} {tail} {up}

This command configures the appearance of the cross-links between hypertext pages obtained for sectioning commands.

       \Configure{crosslinks}
         {}{}{$\scriptstyle\Rightarrow$}
         {$\scriptstyle\Leftarrow$}
         {}{}{}{$\scriptstyle\Uparrow$}

13. \Configure{crosslinks+} {before-top-links} {after-top-links} {before-bottom-links} {after-bottob-links}